BEA LO Linx 80.0240.04 Guide de l'utilisateur télécharger pdf (Page 1)

75.5134.10 EN 20110519 Page 1 of 13

DESCRIPTION

TECHNICAL

SPECIFICATIONS

BODYGUARD III

USER’S GUIDE

COMPONENT ID

INSTALLATION

TIPS

 The sensor must be

firmly fastened to

prevent vibration.

PRESENCE SENSOR

The BEA Bodyguard III Presence Sensor (10BODYGUARDIII) is a self-monitored ready overhead-mounted diffused active

infrared sensing device that provides detection for the triggering of automatic swing door safety functions. This sensor is

designed for use with all of BEA’s LO-21 modules, as well as the Parallink and LO-Linx. When used with BEA’s lockout

devices, the sensor is programmed to allow two different fields of detection - one for detection when the door is in the fully

closed position and the other for detection when the door is fully open. While the door is in the fully open position, the

Bodyguard extends its coverage back through the threshold area of the doorway, to provide coverage that will overlap with

BEA’s motion sensors.

As with all of BEA’s programmable sensing devices, full adjustability is achieved with the use of BEA’s hand-held remote

control unit. This allows alteration of all of the available functions as well as for inquiry of existing settings. Should the need

arise; the Bodyguard may also be tuned by means of two sensor-mounted buttons contained on the PC Board within the

unit. With these two buttons, the Bodyguard’s field of detection can be altered without the use of the hand-held remote. If a

complete door-mounted sensor (SuperScan) system is not used in addition to the Bodyguard, BEA, Inc. recommends the

use of a lockout safety beam to allow safety signaling if the zone is entered during a door closing cycle.

Installation Height - Variable 9’-0” max. (recommended 6’-6” to 8’-0”)

Mounting Angles

Bodyguard only

Bodyguard with Bodymount

+5°, +10° (factory default setting: +5°)

0°, +5°, +10°

Power Supply 12 to 24 V AC / DC +/- 10%

Frequency 50-60 Hz

Output Max. Voltage at contacts: 60V DC / 125V AC

Max. Current at contacts: 1 A

Max. switching power: 30 W (DC), 60 VA (AC)

Relay Hold Time 0.5 to 9 seconds

Operating Temperature -22°F to +140°F

Immunity Immune to electrical and radio frequency interference

Cable 4’- six conductor cable

Weight 1lb. 11 oz. (765g)

Dimensions 11.8”L (305 mm.) x 1.9”H (51 mm.) x 1.9”W (46 mm.)

Material Aluminum & ABS plastic

Housing Color Black anodized aluminum

Left Lens

4’ Cable

Red LED

Right End Cap Left End Cap

Right Lens

Center Eye Shield

 The sensor must not have

any unwanted objects likely

to move or vibrate in its

path.

 The sensor should be

mounted flush with bottom of

door header.

1 2 3 4 5 6 ... 12 13

Résumé du contenu

Page 1 - BODYGUARD III

75.5134.10 EN 20110519 Page 1 of 13 DESCRIPTION TECHNICAL SPECIFICATIONS BODYGUARD IIIUSER’S GUIDECOMPONENT ID INSTALLATION TIPS  The sensor m

Page 2 - Bodyguard

75.5134.10 EN 20110519 Page 10 of 13 BODYGUARD WIDTH PATTERNS BODYGUARD DEPTH PATTERNS Ro

Page 3

75.5134.10 EN 20110519 Page 11 of 13 TROUBLE-SHOOTING BODYGUARD DEPTH PATTERNS - Cont. Row 1 (spots 1 through 6), are on during open door p

Page 4

75.5134.10 EN 20110519 Page 12 of 13 TROUBLE-SHOOTING – Cont. ACCESSORIES

Page 5 - + + then +

75.5134.10 EN 20110519 Page 13 of 13 COMPANY CONTACT ANSI / AAADM COMPLIANCE STATEMENT ANSI / AAADM Compliance AAADM American Association of Au

Page 6

75.5134.10 EN 20110519 Page 2 of 13 SAFETY PRECAUTIONS MECHANICAL INSTALLATION - PREPARATION MECHANICAL INSTALLATION – PLACEMENT OF THE SENSOR

Page 7

75.5134.10 EN 20110519 Page 3 of 13 ELECTRICAL INSTALLATION AND CABLING MECHANICAL INSTALLATION 1. The extrusion has pre-drilled mo

Page 8

75.5134.10 EN 20110519 Page 4 of 13 MECHANICAL ADJUSTMENTS ELECTRICAL INSTALLATION AND CABLING (Continued) 2. Attach the terminal block to

Page 9

75.5134.10 EN 20110519 Page 5 of 13 DUEL EGREES: REDUCING CROSS TALK POWER-UP PROCEDURES 1. Upon completion of mechanical and electrical insta

Page 10

75.5134.10 EN 20110519 Page 6 of 13 BEA’S UNIVERSAL REMOTE CONTROL The Bodyguard is fully compatible with BEA’s Remote Control as shown below.

Page 11

75.5134.10 EN 20110519 Page 7 of 13 PROGRAMMING GUIDE – GENERAL FUNCTIONS AU

Page 12

75.5134.10 EN 20110519 Page 8 of 13 PROGRAMMING GUIDE – PATTERN ADJUSTMENTS THRESHOLD:

Page 13 - ANSI / AAADM Compliance

75.5134.10 EN 20110519 Page 9 of 13 MANUAL (NON-REMOTE) SET-UP Without the BEA Remote Control, the Bodyguard may be set up using the manu

Commentaires sur ces manuels

Pas de commentaire

BEA LO Linx 80.0240.04 Guide de l'utilisateur Page 1

Naviguer en ligne ou télécharger Guide de l'utilisateur pour Ouvreur de porte de garage BEA LO Linx 80.0240.04. BEA LO Linx 80.0240.04 User`s guide [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

BEA LO Linx 80.0240.04 Guide de l'utilisateur Page 1

Naviguer en ligne ou télécharger Guide de l'utilisateur pour Ouvreur de porte de garage BEA LO Linx 80.0240.04. BEA LO Linx 80.0240.04 User`s guide [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Ouvreur de porte de garage BEA LO Linx 80.0240.04